«INT-506540/507059/507172/507219-UM-ML1-0914-07-0 Rackmount LCD Console KVM Switch • User Manual English INTRODUCTION Thank you for purchasing the ...»
MODELS 506540, 507059,
Rackmount LCD Console KVM Switch • User Manual English
Thank you for purchasing the Intellinet Network Solutions Rackmount LCD Console KVM Switch, Model 506540, 507059, 507172 or
507219. For a full list of specifications, refer to the datasheet available at intellinet-network.com.
• Rackmount LCD Console KVM Switch
- Model 506540: 8-Port Rackmount LCD Console KVM Switch, 17”
1.8 m (6 ft.) PS/2 and USB combo cables (8)
- Model 507059: 16-Port Rackmount LCD Console KVM Switch, 17”
1.8 m (6 ft.) PS/2 and USB combo cables (16)
- Model 507172: 8-Port Rackmount LCD Console KVM Switch, 19”
1.8 m (6 ft.) PS/2 and USB combo cables (8)
- Model 507219: 16-Port Rackmount LCD Console KVM Switch, 19”
1.8 m (6 ft.) PS/2 and USB combo cables (16)
• Rear bracket and extension kit
• KVM switch module
• Power adapter
• User manual
1. For both the left and right bracket assemblies, screw the front 2. Carefully place the switch on the mounted brackets and of the bracket to the rack, then extend the bracket and attach loosely attach the front of the switch to the front of the rack it to the back of the rack. using the included screws.
3. Move the rear attachment brackets along the slide bars until 4. Attach the bars to the back of the switch.
they contact the back of the switch.
5. Using the included power adapter, connect the 12 VDC jack on the rear panel of the switch module (above) to an A/C outlet. NOTE:
When the control platform is pulled out to its full extension, the bracket guides lock automatically and the power is turned on to the console.
6. Using the included 1.8 m combo cables, connect the HD15 port connectors on the rear panel of the switch module either to PS/2 ports or to USB ports on the computers to be included in the configuration. NOTE: The Rackmount LCD Console KVM Switch features hotswap capability: Computers can be connected and disconnected without turning off the switch. Be sure, however, that the control platform is powered on before powering on any of the connected computers, and always plug in the mouse before the keyboard.
7. To open the control platform and display the LCD screen, squeeze the handle Front handle lock to release the front lock and lift up. The LCD panel can be t
OPERATIONThe Rackmount LCD Console KVM Switch allows you to select and monitor up to eight connected computers two ways: by simply pressing corresponding buttons or by using a mouse or the touch pad to navigate through the on-screen display (which also provides access to the majority of the control and configuration options).
Buttons Using the buttons is quick and easy, as they are positioned just above the keyboard on the control platform.
• In the highlighted grouping on the right are the PC1 through PC8 buttons used to select and monitor a connected computer, plus the red RESET button, which allows you to re-boot.
• In the highlighted grouping on the left are
another six buttons (from left to right):
- AUTO adjusts the LCD display.
- MENU displays the OSD main menu.
- LEFT and RIGHT re-position the LCD image.
- EXIT leaves the currently displayed screen.
- POWER (red) turns the LCD on and off.
Also located on the control platform is the touch pad (below the space bar), which can be used instead of a mouse for on-screen navigation.
On-Screen Display (OSD) All computer control and switching procedures can be performed using the On-Screen Display (OSD).
• To display the main menu, press Ctrl on the keyboard twice.
• If the OSD menu is set as “Console locked,” you need to input a password each time the main menu appears. If no password has been set, just press Enter to display the main menu. There are two passwords in the OSD: the user password, which is not pre-set; and the factory password, which is “INTELLINET.”
• The OSD always starts at the List screen, with the highlight bar in the same position as when the OSD was exited.
• To exit the OSD, press Esc.
• To move up and down through the menu one line at a time, use the Up and Down Arrow keys. If there are more listed entries than what can appear on the main screen, the screen will scroll.
• To activate a port, move the highlight bar to it and press Enter.
• After you select a port, the OSD menu automatically disappears and the port currently selected is indicated.
Main Screen Headings PN — This column lists the port numbers for all the CPU ports on the installation. The simplest way to access a particular computer is to move the highlight bar to it, then press Enter.
QV — If a port has been selected for Quick View scanning,4displays in this column.
PC — If a computer is powered on and on line,4displays in this column.
NAME — Any name assigned to a computer appears in this column.
ENGLISHFunctions The OSD can be controlled and re-configured using the functions described below.
F1 GOTO — GOTO allows you to switch directly to a port by keying in either the computer’s name or its port number (PN).
• To use the name, highlight “NAME,” press Enter, input the name of the computer, then press Enter to confirm.
If there is a matching name, it will display on the screen.
Press Enter to switch to that port.
• To use PN method, highlight “PN,” press Enter, input the port number, then press Enter to switch. If the port number is invalid, it will prompt you to try again.
• To return to the main menu, press Esc.
F2 SCAN — This allows you to automatically scan from the current selected port through any active and connected computers. While scanning, a small window on the screen indicates the current port number. To stop scanning (and continue viewing the last computer scanned), press the space bar. The scan interval can be set by the user.
F3 LIST — This lets you broaden or narrow the range of ports displayed on the main screen. Many of the OSD functions described below only operate on the computers listed on the main screen (selected by using this function).
• ALL lists all of the ports in the configuration.
• QVIEW lists only the ports that have been selected as Quick View ports.
• POWERED ON lists only the ports that have their attached computers powered on.
• POWERED ON + QVIEW lists only the ports that have their attached computers powered on and have been selected as Quick View ports.
• QVIEW + NAME lists only the ports that have been selected as Quick View ports and have been assigned names.
• NAME lists only the ports that have been assigned names.
Highlight a function and press Enter. When the confirmation icon displays alongside your selection, press Enter to return to the OSD main screen with the newly formulated list displayed.
F4 QV — This lets you select a port as Quick View. Highlight a port and press F4. The s icon displays to confirm your selection. Press F4 again and the icon disappears.
F5 EDIT — This lets you create or edit the name of a port. Press F5 and a pink edit box will appear on the screen. Input a name, press Enter, and the port name will be set and displayed.
F6 SET — This lets you configure the OSD menu. Highlight an option and press Enter to change settings.
• CHANNEL DISPLAY MODE offers three options for what appears in the tip window:
- PN + NAME
- PN (port number only)
• CHANNEL DISPLAY DURATION offers two options for the length of time the tip window remains on the screen:
- 3 SECONDS
- ALWAYS ON
• CHANNEL DISPLAY POSITION lets you re-position the tip window. When the window appears on the screen, use the arrow keys to move it, then press Enter to set the new position.
• SCAN DURATION offers eight options for the amount of time each connected computer is scanned, ranging from 3 to 60 seconds.
• SET PASSWORD lets you change the current password as directed on screen.
• CLEAR THE NAME LIST lets you remove any names assigned to the ports. NOTE: This requires a password.
• RESTORE DEFAULT VALUE lets you return to the default settings. NOTE: This requires a password. The user password will be cleared, but not the factory password.
• LOCK CONSOLE means you cannot switch or scan once this function is activated (neither by using the PC1–PC8 push buttons on the keyboard nor the OSD). Selecting this same option when the console is locked will unlock it. NOTE: Both of these options require a password.
Power On/Off and Reboot When you’re ready to stow the switch after use, follow the steps in Step 9 of Installation.
If you need to cut power to the control platform; for example, to reboot:
1. Turn off the power to all connected computers.
2. Disconnect the power adapter from the switch.
3. After 10 seconds or more, re-connect power to the switch and turn it on.
4. Turn on the connected computers.
ENGLISHThis symbol on the product or its packaging indicates that this product shall not be treated as household waste. Instead, it should be taken to an applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. If your equipment contains easily removable batteries or accumulators, dispose of these separately according to your local requirements. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, contact your local city
office, your household waste disposal service or the shop where you purchased this product. In countries outside of the EU:
If you wish to discard this product, contact your local authorities and ask for the correct manner of disposal.